DT125R ARCHIVE

i've tried everything including adjusting the carb cleaning the airfilter, changing the sparkplug. and the bike still has a hard time reving past 6000 rpm i dont think it's time for a rebuild bc the bike has only 7000 KM on it. if someone could help me to solve this problem it would be highly appreciated...

DTRE/X Kick Start Conversion This is a tutorial for future reference for anyone who is thinking of or is going to carry out a kick start conversion for their DT125RE. This may also help if you are going to dismantle the clutch to replace/inspect or repair. It may also help if you wish to replace the ki...

Hi, my bike dies when i give full throttle and the bike is in neutral! I fixed it one time by adjusting the power valve then i drove it for a couple of miles and then it fu*ked up again :P maybe the power volve adjuster is not working properly? Does any one know? :D Please Help :D Thanks for answers :D P.S Sor...

Nice acceleration and top speed.. :) Check my youtube channel .. :) Gianelli pipe and DEP silencer :) https://www.youtube.com/watch?v=furxlJgSjtQ

I could tell by the photos that this one was going to be all sorts of nasty. The ad was minimalistic and the photos were horribly done. Ad reads TZR 125R 4DL BELGARDA,18000 MILES,HAS NOT RUN FOR 12 MONTHS TURNS OVER, GOOD COMPRESSION,POSTAGE £35 http://www.ebay.co.uk/itm/151079217262?ssPageNa...

Recently bought 2strokmx's DT but as I'm sure you know from pictures, it only has the original tank graphics. So I was looking around but can't seem to find an original kit without talking to a dealer (charge way too much I believe) So I'm going to try and cut a few bits out of some vinyl and see how it goes. F...

	Forum	Replies	Views	Last Post
rev problem yamaha dt 125 BIKE NOT REVING PAST 6000 rpm!!!!! (Preview)	Tuning	22	3599	Jun 14, 2009 by born2race
i've tried everything including adjusting the carb cleaning the airfilter, changing the sparkplug. and the bike still has a hard time reving past 6000 rpm i dont think it's time for a rebuild bc the bike has only 7000 KM on it. if someone could help me to solve this problem it would be highly appreciated...
Kick Start Conversion RE 125 DT Idle Clutch Maintenance Circlips Thrust Washer Bolts Stainless Steel Nut Help Tutorial Modifications Upgrade How to DT125RE/X Kick Start Conversion Tutorial (Preview)	KICKSTARTS	7	15910	Mar 12, 2012 by xGINCATx
DTRE/X Kick Start Conversion This is a tutorial for future reference for anyone who is thinking of or is going to carry out a kick start conversion for their DT125RE. This may also help if you are going to dismantle the clutch to replace/inspect or repair. It may also help if you wish to replace the ki...
dt bike dt125x 125 power valve exhaust DT125X dies when full throttle, in neutral. Help! (Preview)	Tuning	5	1723	Aug 23, 2012 by Uhe-95
Hi, my bike dies when i give full throttle and the bike is in neutral! I fixed it one time by adjusting the power valve then i drove it for a couple of miles and then it fu*ked up again :P maybe the power volve adjuster is not working properly? Does any one know? :D Please Help :D Thanks for answers :D P.S Sor...
dt 125 supermoto 1998 dtr Yamaha DT125R 1998 Supermoto DEP exhaust (Preview)	Videos	3	1401	Jan 25, 2013 by Calum122
Nice acceleration and top speed.. :) Check my youtube channel .. :) Gianelli pipe and DEP silencer :) https://www.youtube.com/watch?v=furxlJgSjtQ
4DL TZR 125 Unmaintained 4DL TZR Engine Unmaintained! ( 1 2 3 4 5 … 10 ) (Preview)	Projects	278	17734	Mar 4, 2017 by Calum122
I could tell by the photos that this one was going to be all sorts of nasty. The ad was minimalistic and the photos were horribly done. Ad reads TZR 125R 4DL BELGARDA,18000 MILES,HAS NOT RUN FOR 12 MONTHS TURNS OVER, GOOD COMPRESSION,POSTAGE £35 http://www.ebay.co.uk/itm/151079217262?ssPageNa...
dt 125 2 stroke 4 graphics custom shroud panel stock First Post / Need New Graphics! (Preview)	GRAPHICS	0	1707	Aug 26, 2014 by MIGHTYMAN
Recently bought 2strokmx's DT but as I'm sure you know from pictures, it only has the original tank graphics. So I was looking around but can't seem to find an original kit without talking to a dealer (charge way too much I believe) So I'm going to try and cut a few bits out of some vinyl and see how it goes. F...